Can you hook up house speakers your car

Then connect the negative home speaker wire to the negative automobile speaker wire. Repeat this process for each home speaker added. If the home speaker has RCA plugs, then go to step 3. Plug an RCA plug into the home speaker. Connect the positive RCA plug wire to the positive automobile speaker wire. Then connect the negative RCA plug wire to the negative automobile speaker wire. Turn on the system and listen to the sound coming out of each speaker to verify everything is working.

Picking The Right Subwoofer For Your Car Stereo

Many after-market speakers will fit into the spaces for the stock speakers, while others will require minor modifications, like the installation of a mounting bracket, the drilling of new screw holes, etc. Be sure to take this into account when you buy your new speakers - the installation processes for differently-sized or shaped speakers can vary in difficultly. Note that many speaker retailers offer online tools for determining which of their products best "fit" your car. Prevent electrical damage by disconnecting your car's battery. As with nearly all types of electrical work, it's important to protect yourself and the electrical system before beginning.

Disconnecting the battery's negative terminal prevents the risk of injury from electric shock or damage to the car's electronics through short circuiting, so be sure to do so before tampering with any of the car's internal electronics. Defer to any instructions provided with your new speakers. Since there's so many different types of speakers available, it's nearly impossible to write a how-to guide that will perfectly cover all of them.

The instructions below are highly generalized and may not apply to every single set of speakers on the market. Whenever necessary, defer to the instructions included with your speakers, as these will be specifically suited to your unique product. Take any panels or speaker grilles off. Nearly all speakers in the interior of a car will be covered with some sort of protective paneling or grill. Before the speaker can be modified or replaced, this barrier must be removed. Pry the grill off with a suitable tool, like a flat head screwdriver, removing any bolts or screws that are holding it in place if necessary.

The work you'll have to do to access your car's factory speakers will vary from car to car. In worst case scenarios, for example, you may need to remove seats, crawl into the trunk to access important bolts or wires, or even remove entire door panels to gain access to the speakers. Remove the factory speaker. Note that the speaker is usually, but not always, attached to a wiring harness, so take care not to rip it out when removing it. If you think you'll need to re-install the factory speakers in the future for instance, if you sell the car , don't forget to save any screws that you remove!

Connect the new speaker to the car's electrical system. Usually, connecting your new speaker is a fairly simple matter of plugging your speaker's wiring harness into the car's wiring harness. However, if your car doesn't have this simple type of connection, you may need to connect your speaker with a soldered or crimped connection. Make sure you match the polarity of the car and speaker's connections. Now that you've connected your speaker, it's important to test the connection so that you don't have to waste time later to fix a problem.

Re-connect the battery's negative terminal and turn on the car's radio or stereo. Listen for sound coming out of your new speaker or look for visible vibrations at high volumes. If your speaker won't work, this means that there is a problem with its electrical connection. Secure the new speaker. Once you're confident that your speaker works properly, secure it in its seat in the door or dash.

If you're lucky, your new speaker will fit in the factory speaker's housing. Refer to the instructions included with your speaker. Install and test any subwoofers. Subwoofers are responsible for the ultra-low, "booming" bass sound that some car owners idolize. If your car came with factory subwoofers, installing new woofers can be as easy as seating them in the existing housing and connecting them to the car's wiring harness.

If your car didn't come with factory subwoofers, however, or you'd like to install additional ones, your task may be much harder. It is not an ideal setup, but if you need it to work without getting a new receiver or subwoofer it might be the only way. I would try connecting a cable from either the Tape or VCR record outputs into the back of your subwoofer. I have recently set them up again, however I only get sound out of one speaker.

Both speakers work, I have the A channel selected, the speaker cables both work. The balance is in the centre, I have tried different input cables and even different inputs to the amplifier I have been using the CD input as default. When I have no inputs inserted if I turn up the master volume to full I get the usually hissing from both speakers nothing crackly. The receiver only gets sound from one of the two channels either the left or the right instead of getting both channels like it normally would. Since you hear the hissing noise when you turn up the volume, your receiver can output sound to both speakers.

But if it can only get one of two channels from the RCA inputs, it will only output that one channel. To get it fixed, it might be as simple as re-soldering a connection between the inputs and the amp or it could be something more complicated and expensive. If you want to get it fixed, I would recommend contacting United Radio since they specialize in repairing Sony equipment.

You will have to ship it to them and then they give you an estimate for repair if it can be repaired. In total, it could be almost as costly as buying a brand new Sony receiver with a warranty. You might be able to find someone who does repair local to you, but with equipment like surround receivers, parts might be expensive or impossible to get.

Hi Nick, first off your setup instructions are great! We are looking to build a new stereo system. Will Sonos wireless speakers Work with this setup with home wifi or can you recommend one that will? Thank you in advance! The Yamaha R-S receiver works best with traditional wired speakers.


  • dating sites in kampala uganda;
  • How to Connect a Stereo System | Stereo Barn.
  • How to Use Home Speakers for Car Surround Sound;

The only way I can think of to hook up Sonos wireless speakers like the Play 5, 3, 1, or PlayBar to your stereo is a bit complicated:. I recommend sticking with regular wired speakers for your stereo system and if you want a second system for wireless speakers, go for the Sonos. The Sonos wireless speakers are great for playing music from the internet, but mixing in traditional sources like a CD player or turntable complicates how you have to set your system up and use it.

If there were any good wireless speakers you could directly hook up to a stereo receiver, I would recommend them. I am trying to hook up my sony t. On the back of your TV, look for an audio output. You will either find a red and white analog audio output, an optical audio output, or both. Next, find an input on the back of your Onkyo receiver. If your receiver has an optical audio input, use that because it will give you the full, digital sound straight from the TV. You will need an optical cable to do this.

If not, use the regular red and white analog audio input for your TV. You will need an analog audio cable to do this. Finally, set your receiver to whatever input you used for your TV. Some receivers have a TV input, so use that if you can. Nick, Thanks for your concise and intelligent guide. If you have any suggestions to add to this guide, feel free to let me know. I do not have a system of any kind outside of a Bluetooth speaker that I use for streaming from my phone. I am going to purchase a record turntable looking at the Audio-technica at-lp60 turntable.

I was told that I should buy an older receiver with phono on it and have found some older kenwood and pioneer receivers at a local pawnshop that are reasonable. My question is that I want to listen to the turntable in different rooms then it is in and would prefer to buy a wireless speaker system. Can you connect wireless speakers to an older receiver like that or is the technology not compatible? Any other way I could accomplish it? To answer your question, yes it is possible to connect speakers wirelessly. You can do this with a wireless receiver and transmitter kit like the Soundcast SurroundCast.

Run a car sub off a home receiver?

The advantage of this setup is you can use your turntable with your stereo receiver and listen with any pair of speakers wirelessly. However, this type of setup will compromise the sound quality and the volume level you can listen at for the convenience of wireless speakers. If you turn the volume level up too high, it could blow the speakers or the wireless receiver. I have an old technics model sa-gx stereo receiver and I used it about a week ago everything was working great, but I recently moved it and tried playing the radio.

The volume on high but it sounded so low. How do I get it where the volume can return to normal install of low? It sounds like one or a few things might be a problem:. I always try swapping out as many parts of the system as possible to see what may be wrong. The easiest thing to try is swap out the speaker wires.

Speaker wires can be damaged even if they look fine and this may cause problems with the receiver. Next, try different sources of music like a CD player or iPod. Try your speakers on another stereo receiver. If they sound the same on a different receiver as yours, then the problem may be the speakers. If the speakers sound noticeably better, the problem may be the receiver. Try taking it back to the store you bought it an see if they can test the receiver on one of their stereo setups. Also, try calling Technics and see if they have any authorized repair centers near you.

And is it the wires or stereo? To figure out where this problem might be, test each individual piece of equipment first the stereo receiver, then the speakers, then the speaker wires, and so on on a second stereo system that you know works. So try playing your stereo receiver on a different set of speakers and wires, then try playing your speakers on a different stereo receiver, etc. This will narrow down your search to find which piece of equipment is causing the problem. It might be something as simple as replacing the speaker wires. Just like cars, electronics wear out from time and use.

Like Ann, I would like to use wireless speakers with my vintage system. Is this possible, can you suggest adapters to do this, as well as wireless speakers that would be appropriate. I do not want to spend a lot of money on this. To play wireless music from your vintage system to speakers, I would recommend the Soundcast Surroundcast: This will let you hook up any small sized speakers to it so you can play music from your sound system to wherever you want your speakers to be.

When I play from my iPhone, only one of the two speakers play and the sound comes out stuffy because the bass plays louder than the normal sound. When I play from my laptop, both speakers play but the same happens, stuffy sound. But when I play radio or music from an USB flash drive it works perfectly. Call the store you got the speakers from, they might know how to help since they sell that brand. Just bought some newish Kenwood speakers off some guy.

You need to connect the turntable here because it needs extra amplification compared to the CD and VHS players. Otherwise, you will barely be able to hear the turntable. In this case, connect a red-and-white audio cable from the audio outputs on the cable box to any red-and-white audio input on the receiver. You need a red-and-white audio cable with a ground connector like this:. You might not need it for this system. Can you tell me where everything goes? And do I need both the amp. Then, connect the speakers to the Sansui stereo. As it is, your Sansui stereo will connect all your inputs and amplify the sound for your speakers.

To use your Technics amplifier, you would need a preamplifier to connect all your inputs. Hello I moved into a house that has the whole house surround system built into ceiling and I just purchased a receiver and had five people yesterday trying to get sound from the speakers.

Video of the Day

There is Just 3 audio video red white yellow cords coming from the floor and my receiver for audio has spots for the regular speaker wire. They will best be able to find where the speaker wire goes to and how it hooks up to a surround system. Am not sure in what order to connect the audio RCA jacks to it from dvd player, vcr player, roku 2, cable box and video phone. Tape 1 and Tape 2 record jacks are inputs, but can the playback jacks also be used as inputs?

Have monitor on button for both tapes. From the inputs you describe, you might only be able to hook up 3 devices to this Sansui receiver. The inputs you can use are:. The phono input will only work with a turntable because it has extra amplification meant for a turntable only. If you want more inputs, consider adding an analog audio switcher to your receiver. Do you need two rca cables for each side? Or just one in the amp and on the recording side? But will side A still play? I found a way to connect the red and black speaker wire to a 3.

Can I use a jack splitter coming out of tye iPod and plug in one speaker to each hole in the splitter? Connect a speaker wire to each speaker 2. Connect the speaker wire to the speaker outputs on the amplifier 2. Connect an aux cable from the iPod to a red and white audio input on the amp. Do I use one of the Video connections or Phono or what? The only exception to this would be the Phono input; avoid using that one because it is meant for a turntable only.

A set of 3 Bose Accoustimass 7 speakers plus sub woofer came with it - we inherited it all. Two of the Bose speakers have died, so we ordered some more off of ebay. When I initially hooked up one new speaker and compared it to the original, the sound did not seem as clear. Then I switched them, and the second one was definitely less clear. I then switched back to the first new speaker, and it was fuzzy too!

At this point, I am waiting for my husband to re strip the speaker wire which was new in and see if that helps.

Can you advise me as to what could cause this fuzzy sound? Also, with the 2 wire speaker wire, does it matter which one goes in which hole black or red? Could this effect speaker performance? The attachment on the Bose speakers has the button you push in, push in the wire and it is attached. Try testing out each individual piece of equipment first the speakers, then receiver, then speaker wires, and so on with a second system that you know works.

So, try the receiver on another set of speakers and speaker wires, or try the speakers on another receiver. Just like a car, electronics will wear out with time and use. As for your question about which hole the red and black speaker wire goes into, yes this could effect the speaker performance. When you connect speakers to your receiver, make sure the wires connect the red to the red ports and black to the black ports.

The Kenwood DC is the controller or preamplifier for your system. This is where everything connects to. There should be a CD player input on the DC One end of my speaker wires are stripped of the coating and the other end is a plug. There are no holes for plugs on either the speaker or the receiver. Do I need to cut off the plug and strip the wires on the offending end? It sounds like you need to cut off the plugs and strip the wire. Some speaker manufactures cover the plug holes on speakers with red and black plastic caps.

This picture shows what they typically look like:. Hello I would appreciate some advice re a problem I have: I just got the whole system out of storage where it has been since when I went overseas for work. The CD input is being used by the CD player. Can I use the Tape inputs? If so which two of the four can I safely use? I thank you for your time and kind consideration. I have no idea how to wire these, any help would be appreciated, and what else would I need to set them up? I would like to set it up so that it has an auxiliary cord or something similar so I can play music from my phone.

I got a pair of Fisher SR speakers from my shop teacher for free as he was going to throw them out. I want to set them up so I can play music from my phone, lIke an auxiliary corder or some thing similar. What else do I need and how would I set them up? Any help will be appreciated. To listen to music from your phone to your stereo speakers, I would recommend a stereo receiver like the Integra DTM As an alternative to Integra, I would also recommend stereo receivers made by Marantz, Onkyo, Denon, etc. The only other part you would need to play music from your phone to your speakers is an aux cable.

This will have a headphone jack on one end to plug into your phone and on the other side, it will have the standard red-and-white audio plugs that go into the stereo. Any suggestions on if we have enough to get started? I truly appreciate your time and any suggestions you have.

It sounds like you got some really good used stereo equipment. My dad has Snell speakers and he loves them! In addition to being able to plug in your CD player, turntable and anything else you want to play sound from, a pre-amp will let you control the volume of your sound.

The preamplifier then outputs the right type of signal to your amplifier which then plays through your speakers. If you want something new with a good, basic layout, checkout the Parasound Zpre2 — http: It has 4 audio inputs — enough for your CD player, turntable, plus two more inputs of your choice — and it has a variable output which you need when connecting the pre-amp to your amp.

Of course, there are other new pre-amps out there but they can go up into the thousands of dollars.

Full Car Audio System Installation - Speakers, Subwoofer and Amplifier

You can get a great deal on a used surround sound preamplifier and play it in stereo mode. People are always trying to get rid of video equipment because video technology updates nearly every year. New HDMI connections and surround sound formats can make a ten year old surround sound pre-amp obsolete compared to something new. Thanks for sharing your knowledge with all of us! Can I just strip the RCA end and connect the bare wire into the receiver? If not, what is the best way for me to connect it? I have a 2 channel receiver and CD player. However everyone is telling me that I need a DAC.

I understand that the chip in my sound card may be lousy and all of the other reasons I have read about on countless forums and in countless articles. But is it absolutely necessary? I do not need a headphone amplifier, or a volume controller. I am woefully ignorant, as you have no doubt gathered, and do not know if I truly need one or, if in fact I do, which one is the right one for my particular set up.

Yes, you can use a minijack to RCA cable to play music from your Macbook to your receiver. This sounds great for most listening purposes. If so, your receiver has a DAC built into it. If you want, try it out and see how it sounds. I picked up the following JVC package at an estate sale…. Not sure if it has one to be honest. Anyway, the components are: I have a box of wires to boot.

My questions are pretty basic. Thanks for any tips or help in advance. It sounds like you found a really good stereo system. In some cases, this cable is already attached to the turntable, in other cases you have to plug it in yourself. This is what it looks like —. You will need an RCA cable with a ground cable attached that looks like this:. The reason you need a phono preamplifier or phono input on a receiver is because the type of signal that comes out of the turntable needs extra amplification compared to any other piece of equipment like a CD player, tuner, tape player, etc.

Without it, you will barely be able to hear your turntable.

How to Connect Home Speakers to a Car Stereo | It Still Works

Depending on the model of TV and receiver you have, there are a number of ways you can do this. Any knowledge on this hook up? I am hooking up Kljpsch 7. You can use just 2 conductors — for example, use the red and black wires for your speakers and leave out the green and white wires. You can use all 4 conductors — like you said, you can twist together 2 conductors each for the positive and negative connections. I like option 2 the best because you get to use all 4 conductors in the speaker wire. Hi i have my kenwood krvd home theater soround sound and kenwood eualizer ke preamp kcand power amplifier all are kenwood im trying to hook up all the units but it doesnt work.

Hello, have almost the same set up….. I am thinking about buying a full on cassette deck with an amplifier. Can I use the deck also as an amplifier connected to my television? Thank you so much for the very clear instructions. You have the patience of a saint. Hi Nick, First, thanks for all the help and comments to all the people here. I recently received a system I am having trouble understanding how to connect. I am looking at a Quad 33 preamp, and two quad s poweramps.

The quad 33 has apparently a special cable that splits the single output from the preamp to the two amps this I understood thanks to the glorious internet , and this is clear. Now after this, I need to connect each amp to 1 speaker, which is where I run into trouble. Should I simply attach both positive outputs from both channels of the amp, into the 1 positive input of the speaker? Thanks in advance, and sorry for the non-professional mumbo-jumbo!

Hi Nick, I am replacing my speakers. Keeping my Polk Monitor 10Bs. Also, have old Monster Z series cables. Any recommendation on replacing these? Are they too old to use? I moved to paint the self it was on and removed the speakers. I have the clip with bare wires to connect to the speaker and the receiver. It worked fine until I moved it. I have a question. I have a stereo system like the above one in your instructions.

Is there any way I can connect my iPhone to the speakers? I need to know if you can connect the DVD player to the tv. How could you do that? The stereo is working from being connected like showen above. I have a kenwood vr and I want to hook up three speakers two for left and right and one for the center but I have it all hooked up but no matter what mode i choose i can never get them to all three play at the same time only either the left and right alone.

Or the center alone. I recently aquired a new jbl studio series s and tried connecting it to my current home theater system. I then split the wires coming from the speaker and put half in the subwoofer port, and the other half in the front center port. Do you know what could be causeing this, and how I could potentially fix this? I have a Pioneer vsxk receiver my house came with speakers built in, 2 in the family room 2 in the upstairs master bedroom and two in the foyer, the back of the receiver has spots for front LR, center, and surround sound LR.

I can get the family room speakers to play but not the rest. The up stairs bedroom plays sometimes but ill cut off. Hi Nick, I have kenwood A7j and was wondering what is the function of Adapter input which has a ground connection, secondly what is the long term effect of using a 4ohms rated speaker instead of the recommended ohms. Your response will be highly appreciated. Is it ok to hook up a powered amp to a cd player that has volume control or is that bad? He wants it hooked up so he can listen to music in his hangar. I have speaker wires with red, yellow, and white ends.

I have an audio cable with yellow and white ends. Please help, I know these are old systems. They worked great the last time we had them hooked up. Yeah, I know how dumb that was now. They have to have wires because there are no ports to plug red or yellow wires in to. Should I trash this whole system although it has great sentimental value to us? Is there any way you can take pictures of the back of the Panasonic receiver and the speaker cables, then upload them or send them to my email nick stereobarn.

This would help me figure what type of speakers would work for you. Good Evening , have a small hard drive -power spec — with songs and artist name and song name. I can play it threw my TV and Laptop. I am so lost. I wanted to go vintage for my stereo system. My last system went off with out a bitch. Could play my record player and my mp3. I have two cabinet technics speakers connected to a phisher amp and tuner.

I bout these at a thrift store. I have it connected right. What am I doing wrong? Do they just not work? I have a question on setting up my stereo. I followed the Denon set-up instructions, but no sound comes out of the subwoofer or the Onkyo speakers. Thanks a lot for this guide. I am ready to buy a second hand Denon DRW cassette deck to be able to re-enjoy my year old cassettes. I only use RCA cables. I am worried though that the cassette deck might not work. Is this a possibility? Hey Nick, I just got my old 80s Scott receiver down from the attic for te garage.

Its two speakers both have 4 wires, black and red, black and red, which plugged into the back of the units 8 recepticles. The receiver has only 4 places to hook them into. I tried hokking both left and right to left and right. What do you suggest? I am not so much interested in bluetooth or wireless.. I am located in austin texas and like to put my eyes on the prize before I buy. They are not a matched set.

I think I need a preamp to get the speakers to work. Hello, there are two speakers label led A and B, but in the picture you have the wires for the speaker B upper and lower connected to the receiver. There is no use of speaker A? I have a Speaker distribution system, an integrated stereo amplifier is that the receiver?

Which of the first 3 component items do I have to hook up — just the amplifer? I have more limited space than I did previously.